repair welding
英 [rɪˈpeə(r) ˈweldɪŋ]
美 [rɪˈper ˈweldɪŋ]
网络 补焊; 返修焊
双语例句
- Tele-operated TIG welding robot for hyperbaric underwater pipeline repair welding
遥操作干式高压海底管道维修焊接机器人系统 - Microstructure and Improvement Measures of Railway Wagon Side Frame after Repair Welding
铁路货车侧架焊补后的组织缺陷及改善措施 - Study on the Damage Problem of the Super-high Pressure Tubular Reactor in Safety Engineering Tele-operated TIG welding robot for hyperbaric underwater pipeline repair welding
超高压管式反应器安全工程中损伤问题的研究遥操作干式高压海底管道维修焊接机器人系统 - Repair welding shall be performed only according to approved procedures and by qualified welder;
补焊只能由合格焊工按规定程序实施； - Repair welding for defects should be controlled in accordance with in the Welding Repair Procedure ( NQCP-09/ 02).
缺陷修补焊接应遵照焊接修补程序（NQCP-09/02）的要求进行控制。 - Mainly used for various hardened iron blade repair welding.
主要用于各种淬火后铸铁的刃口修补焊接。 - WC-cored electrode is a repair welding electrode with high hardness and high wear resistance, which has been widely used in circumstance with violent wear.
WC型管状焊条是一种高硬度、高耐磨性的堆焊焊条，广泛用于强烈磨损的零件上。 - Detailed description is done on repair welding technology.
对补焊工艺作了详细说明。 - This paper deals with the procedures, steps and precautions for repair welding of the bucket rod and the rack.
文章介绍了斗杆、齿条焊修的程序、步骤和注意事项。 - Some measures have been taken to eliminate the defect, for instance, using dry, warm nitrogen of low pressure as sealing gas, securing supports of pipes and using repair welding.
后采用将密封气改为干燥加热的低压氮气、对管线进行加固支撑和补焊等措施，成功排除了故障； - Study on the Repair Welding Technology In Shaped Roll for Outlet Flange
出口法兰型钢轧辊焊接修复工艺研究 - The causes of resulting in the cracks are discussed and the proper techniques of repair welding the cracks are presented in this paper.
本文就裂纹产生的原因和如何正确安排焊补工艺进行讨论。 - Repair welding for iron cast parts of Daihatsu diesel engine
大发柴油机机身和机座铸铁件补焊部位与工艺 - By comparison with manual arc welding, it is found that the thermit welding is a efficiency, energy saving and high quality process for repair welding of steel ingot die.
根据对比铝热焊与手弧焊修复工艺，阐明了用铝热焊修复钢锭模是一种高效、节能、焊接质量好的新方法。 - Study on the Application of Plasma Arc Powder Repair Welding in Restoring Petroleum Drill Stem Joint
等离子弧粉末堆焊在石油钻杆接头修复中的应用研究 - A new procedure for repair welding of white cast iron roller is presented and analysis is carried out to the results.
介绍了白口铸铁轧辊焊接修复新工艺，并对其结果进行了分析。 - Application of repair welding on surface hardening of steel body PDC bit
堆焊技术在钢体PDC钻头表面硬化中的应用 - Repair welding technology of allocating convex for dry gas seal in barrel type centrifugal Compressor caused by operation fault is introduced.
介绍了筒型离心式压缩机干气密封凸台由于操作上造成的缺陷，从而进行的补焊工艺。 - The vibrating mechanism of surfacing for repair welding of shaft is developed; the frequency and amplitude of electrode vibration can be altered.
设计了用轴类零件修复的频率和振幅均可调的振堆焊机构。 - This article discusses repair welding on defects found in Cr-Mo and Cr-Mo-V casting steel pieces such as casings after finish-maching and in the operation.
论述了汽缸等Cr-Mo与Cr-Mo-V钢铸件在精加工及在电厂运行中所产生的裂纹等缺陷修复问题。 - A New Repair Welding Procedure for Cr-Mo-V Steel
Cr-Mo-V钢冷补焊新工艺研究 - This paper introduces the repair welding procedure for repairing an alumal casting piece of an oil pump cylinder, This method covers the shortages of AC argon arc weld and gas welding.
介绍了对油泵机缸体铝锰合金铸造件缺陷补焊修复的技术工艺，且弥补了若采用交流氩弧焊和气焊施焊时存在的不足。 - Because of selecting super low hydrogen electrode which had the same chemicals with the base metal, and using reasonable welding procedure during site welding, the excellent quality of repair welding was guaranteed.
论文叙述了在现场施焊工艺中选择了与母材化学成分基本相同的超低氢电焊条和其它严格的焊接的工艺措施，确保了优质焊接质量。 - Study on the Repair Welding of the Punch Mould
冲压模具焊补之研究 - Repair Welding Joint Boundary Structure and Performance of Explosion Composite Plate
爆炸复合板补焊接头界面的微观组织与性能 - The repair welding technology and inspecting method after welding are mainly discussed.
重点讨论了补焊工艺及焊后检查方法。 - Application of Repair Welding Technology for The Wear Resistant Layer of Blower Rotor
鼓风机转子耐磨层补焊技术的应用 - Study on Repair Welding Small Defects for Gray Iron Castings
灰铸铁件小缺陷焊补的研究 - The Development and Application of the Casting Defect Repair Welding Machine
铸件缺陷补焊机的研制与应用 - Repair welding and local stress-relief heat treatment ( LSRHT) is usually employed in case defects such as cracks are found.
使用中发现裂纹等缺陷后通常需要进行补焊和局部消应力热处理。